STUDY OF THE ELECTRICAL LOADING OF SEMICONDUCTOR SWITCHING ELEMENTS IN A STEP VOLTAGE REGULATOR

BARUDOV Emil, BARUDOV Stefan and PANOV, Emil

Technical University Varna, 9010, No.1 Studentska str.

E-mail: ugl@abv.bg

Abstract : The voltage of the separate consumers in limited power networks can be maintained within the allowed boundaries by automated step changeover of an autotransformer. The transient phenomenon of a thyristor switch breakeover at the boost winding of the autotransformer is studied.

Keywords: step changeover, autotransformer, regulator, model, transient process.

Introduction: There are electrical networks where the phase voltage varies far above the allowable limits depending on the operational modes of some of the ultimate consumers. This forces application of individual regulation of the phase voltage directly at the very consumers. The regulation can be effected by stepwise automated changeover of the autotransformer terminals. The general principles related to the solution of similar problems are discussed in [1...5].

The operation of the stepwise voltage regulator is determined by the length of the transient process of the individual semiconductor switches and by the electrical load in transient mode. The length of the transient process is analysed in [6].

The present task is to study, at the same conditions, the electrical loading of the semiconductor switches in transient mode of operation.


Fig. 1 Arguments and functions diagram of the study.

The examination is equivalent to a study in multidimensional space, where three of the considered variables are: regulator input voltage, initial phase of switchings and load current, while the lentgth of the transient process and the regulator current amplitudes are functions.

Figure 1 shows graphically the axes of this multidimensional space and thus the complexity of the study.

Figure 2 presents the model of voltage regulator with parameters ecountered in the computer sumulations. Fig 3 shows the equivalent circuit of the transient process The switching elements are idealized, i.e. their ohmic resistances are assumed to be equal to zero.

On the basis of the developed program  AVTO1 under MATLAB, we receive the values of the currents at the respective change of the switching phase, as well as the character of the load. Examinations are made for currents I2max  Itmax, I3max I4max - switching currents of  2 and 3 switches.

The computer simulations display the following regularities:

Regarding the load current I2max:

In case of active load,  I2max is largest at φ=90; 270 and is minimal for φ=0; 180; 360.

Sinusoidal distribution of the  I2max - phase relationship is observed (Figure 4).

At active-inductive load  I2max does not depend on the phase in 0-180 and 180-360 intervals (Figure 5).

In case of active-capacitive load I2max has sinusoidal distribution. Overcurrents are observed at  φ=112,5 and 292,5 (Figure 6).



Fig.2 Equivalent circuit of the step voltage regulator

Fig. 3 Equivalent circuit of the transient process.

The following is observed for the switching current I3max :

With active load, I3max has maximal values at φ=45; 225, and minimal at φ=0; 180; 360. Overcurrents are observed at φ=45; 225 (Figure 7).

At active-inductive load, I3max is largest in  [0; 45] and [180; 225] intervals. Overcurrents are observed in these itervals, while for the rest of them  I3max has minimal values (Figure 8).

At active capacitive load, I3max is grouped around sinusoidal distribution.  Overcurrents are observed with some spread in the intervals [112,5; 202,5] and [292,5; 22,5] (Figure 9).

The following is observed for the switching current  I4max :

With active load I4max has maximal values at φ=45; 225. Overcurrents are present at these phases while the minimal values are at φ=0; 180; 360 (Figure 10).

At active-inductive load I4max has maximal values in the intervals [0; 45] and [180; 225], while the minimal values are located in the rest of the intervals (Figure 11).

At active capacitive load, I4max is grouped around sinusoidal distribution with some spread in the [67,5; 180] and [247,5; 360] intervals overcurrents are present there (Figure 12).

Figures 13 and 14 show in the time domain the reaction of the load current i2(t) and the current i3(t) through the closing 3 switch, for ZT=3,3846.e- j 75 and series equivalent load circuit at φ=202,5 initial switching phase. It is evident that the currenti3(t) reaches i3max=-950 during the transient process.

Figures 15 and 16 present the load current i2(t) and the current i3(t) for ZT=3,3846.e- j 75 and series equivalent load circuit, at initial switching phase φ=112,5. Both currents reach maximal values of  330.

Fig 4 Dependence of  I2maxcurrent from the switching phases.

Fig. 5 Dependence of  I2maxcurrent from the switching phases.

Fig. 6 Dependence of  I2maxcurrent from the switching phases

Fig. 7 Dependence of  I3maxcurrent from the switching phases

Fig. 8 Dependence of  I3maxcurrent from the switching phases

Fig. 9 Dependence of  I3maxcurrent from the switching phases

Fig. 10 Dependence of  I4maxcurrent from the switching phases

Fig. 11 Dependence of  I4maxcurrent from switching phases

Fig. 12 Dependence of  I4max current from the switching phases.

Fig. 13 Time domain response of  i2(t) current for R-L load.

Fig. 14 Time domain response of  i3(t) current for R-L load.

Fig. 15 Time domain response of  i2(t) current for R-C load.

Fig. 16 Time domain response of  i3(t) current for R-C load.

CONCLUSIONS

The examinations show that emergency states exist for the three types of loads (active, inductive and capacitive), occuring at specific values of the starting phase of switchings i.e of the transient process. This requires special control identifying the type of the load and tracking the phase of onset of  switching.  This control should select the switching moments in a way alowing as short as possible transient processes with minimal amplitudes, i.e. to provide accurate activation of the switches. This can be achieved under microprocessor control, monitoring the operation of the regulator.

REFERENCES

[1]  Minchev ., Penchev P. Contactless Aparatuses, Technika 1976 (in Bulgarian)

[2] Porudominskiy V. Switching Devices for Transformers under Load, Energia 1974 (in Russian)

[3] Lipkowskiy . Transformer-Switching Actuator Structures of the Alternating Current Converters,  Naukova Dumka 1983 (in Russian)

[4] Barudov St., Dimitrov D, Barudov Em. Functional Performance of Transformers in a Contactless Voltage Stabilizer  SIELA 2001 (in Bulgarian)

[5] Barudov Em., Barudov St., Panov Em. Switching Processes in a Step Voltage Regulator, Annual Proceedings 2003, Technical University Varna.

[6] Barudov Em., Barudov St., Panov Em. Study of the Length of the Transient Process in a Step Voltage Regulator.